Why Learning Plumbing Basics is Crucial for Bathtub Installation
Why Learning Plumbing Basics is Crucial for Bathtub Installation
Blog Article
On this page below you'll find a lot of reliable information in relation to How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.
Mounting a tub isn't exactly rocket science, but it does need strong plumbing, carpentry, and also in some cases, tiling abilities. Changing an old bathtub with a new one is additionally a moderately challenging task. If the old tub is easily obtainable, the project can move speedily; if you have to open up a wall surface to remove the old bathtub and also place the new bath tub, the task is much harder. In either case, the project is within a house handyman's abilities, although you will need a helper to leave the old tub as well as embeded in the new one. Make certain you have actually qualified on your own for the job as well as are comfortable attempting it. Instead of employing a specialist to take control of a halfway-completed project, it is much better to consider using one before you start. Possibilities are you might require an expert plumber to make tube links.
This post will certainly aid you mount a brand-new bath tub in your washroom if you have actually currently acquired a brand-new tub and also don't require to transform the setup of your previous water pipes.
Your tools and also material checklist need to make up the following:
Planning for the Setup
To start with, the sustaining frame provided with the bath must be fitted (if required) according to the maker's instructions. Next off, fit the faucets or mixer to the bathtub. When fitting the faucet block, it is very important to make sure that if the tap includes a plastic washer, it is fitted between the bathroom and the faucets. On a plastic bath, it is also practical to fit a sustaining plate under the taps device to avoid strain on the tub.
Fit the versatile tap connectors to the bottom of both taps using 2 nuts and also olives (sometimes supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and then pass the electrical outlet through the hole in the bathroom. Make use of the nut provided by the manufacturer to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the adaptable overflow pipe to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which need to be fitted inside the bathroom. See to it you use every one of the supplied washing machines.
Link the trap to the bottom of the waste electrical outlet on the bath tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and also screw on the trap to the outlet. Connect all-time low of the overflow tube in a comparable manner.The bath ought to currently prepare to be fitted in its last setting.
Removing Old Touches
If you need to change old faucets with new ones as a part of your installation, after that the first thing you need to do is separate the water system. After doing so, turn on the faucets to drain any kind of water continuing to be in the system. The procedure of eliminating the existing taps can be fairly problematic because of the restricted gain access to that is usually the instance.
Use a container wrench (crowsfoot spanner) or a faucet device to reverse the nut that connects the supply pipelines to the faucets. Have a towel prepared for the remaining water that will certainly originate from the pipelines. As soon as the supply pipes have been gotten rid of, make use of the very same tool to loosen up the nut that holds the faucets onto the bath/basin. You will certainly require to quit the solitary taps from turning throughout this process. When the taps have been gotten rid of, the holes in the bath/basin will have to be cleaned up of any old securing substance.
Before proceeding to fit the new faucets, contrast the pipeline links on the old faucets to the new taps. If the old faucets are longer than the new taps, then a shank adapter is needed for the new taps to fit.
Mounting the Bath tub
Using both wood boards under its feet, place the tub in the called for position. The wood boards are useful in equally spreading the weight of the tub over the location of the boards instead of focusing all the weight onto 4 tiny factors.
The next goal is to guarantee that the tub is leveled all round. This can be accomplished by examining the level as well as adjusting the feet on the tub up until the level reads level.
To set up faucets, fit the bottom of the outermost flexible faucet adapter to the proper supply pipeline by making a compression sign up with; then do the same for the various other tap.
Activate the water as well as check all joints and also new pipework for leakages and tighten them if essential. Fill the tub as well as likewise examine the overflow outlet as well as the regular outlet for leakages.
Finally, repair the bathroom paneling as defined in the supplier's instruction manual. Tiling and sealing around the bathtub ought to wait until the bathtub has been used at least once as this will certainly resolve it right into its last setting.
Fitting New Taps
If the tails of the brand-new faucets are plastic, then you will require a plastic port to avoid damage to the string. One end of the port fits on the plastic tail of the tap and also the various other end offers a link to the existing supply pipes.
If you require to fit a monobloc, then you will need minimizing couplers, which links the 10mm pipe of the monobloc to the standard 15mm supply pipe.
Next, place the faucet in the placing opening in the bath/basin making sure that the washing machines remain in place in between the tap and also the sink. Secure the faucet in position with the producer provided backnut. When the tap is firmly in place, the supply pipelines can be linked to the tails of the faucets. The taps can either be linked by utilizing corrugated copper piping or with typical faucet adapters. The former kind should be linked to the faucet finishes initially, tightening only by hand. The supply pipelines can later on be connected to the various other end. Tighten up both ends with a spanner after both ends have actually been connected.
Tiling Around the Tub
In the location where the bathroom fulfills the tile, it is needed to secure the accompanies a silicone rubber caulking. This is essential as the fitting can move sufficient to crack a rigid seal, creating the water to pass through the wall surface in between the bath as well as the tiling, leading to complications with wetness and feasible leakages to the ceiling listed below.
You can pick from a range of coloured sealers to assimilate your fixtures and also installations. They are marketed in tubes and cartridges, and also are capable of securing spaces up to a size of 3mm (1/8 inch). If you have a larger space to load, you can fill it with spins of soaked paper or soft rope. Keep in mind to always fill up the bath tub with water before securing, to permit the movement experienced when the tub is in usage. The sealer can fracture fairly early if you do not think about this movement before sealing.
Conversely, ceramic coving or quadrant tiles can be used to edge the bath or shower tray. Plastic strips of coving, which are easy to use as well as reduce to dimension, are also easily offered on the marketplace. It is recommended to fit the ceramic tiles making use of waterproof or water resistant adhesive as well as grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
We are very interested in Installing A Bathtub and I'm hoping you appreciated our blog posting. Enjoyed reading our entry? Please share it. Let someone else locate it. Thank you for your time. Visit again soon.
Dial, we'll rush! Report this page